 |
HP TCP/IP Services for OpenVMS
Installation and Configuration
Enter an address prefix to use on interface ITn [DONE]:
|
If a router is not advertising a global address prefix on this
tunnel interface, enter a 64-bit address prefix. You can configure
multiple address prefixes for this configured tunnel. You are prompted
for additional address prefixes until you enter DONE.
If you do not
want the host to use an IPv6 address prefix on the tunnel interface,
press Enter.
The configuration procedure asks whether you want to create another
IPv6-over-IPv4 configured tunnel:
Create another IPv6 over IPv4 configured tunnel? [NO]:
|
If you want to create another IPv6-over-IPv4 configured tunnel,
enter YES. The procedure repeats steps 12 through 14 for each
additional configured tunnel you choose to create.
If you do not
want to create another IPv6-over-IPv4 configured tunnel, press Enter.
The procedure continues at step 16.
Indicate whether you want to create an IPv6-over-IPv6 configured
tunnel:
Create IPv6 over IPv6 configured tunnels? [NO]:
|
If you want to create an IPv6-over-IPv6 configured tunnel, enter
YES. You are prompted to enter information about this tunnel in
subsequent steps.
If you do not want to create an IPv6-over-IPv6
configured tunnel, press Enter; the configuration procedure continues
at step 21.
Enter the tunnel's source IPv6 address in response to the following
prompt:
Enter the source IPv6 address of tunnel ITn:
|
Enter the tunnel's source IPv6 address in the dotted-decimal format
(d.d.d.d).
Enter the IPv6-over-IPv6 tunnel's destination IPv6 address in
response to the following prompt:
Enter the destination IPv6 address of tunnel ITn:
|
Enter an IPv6 address in dotted-decimal format d.d.d.d.
The tunnel's destination address must differ from the source address
entered in step 17.
Enter an address prefix to use on the tunnel interface:
Enter an address prefix to use on interface ITn [DONE]:
|
If a router is not advertising a global address prefix on this
tunnel interface, enter a 64-bit address prefix. You can configure
multiple address prefixes for this configured tunnel. You are prompted
for additional address prefixes until you enter DONE.
If you do not
want the host to use an IPv6 address prefix on the tunnel interface,
press Enter.
The configuration procedure asks whether you want to create another
IPv6-over-IPv6 configured tunnel:
Create another IPv6 over IPv6 configured tunnel? [NO]:
|
If you want to create another IPv6-over-IPv6 configured tunnel,
enter YES. The procedure repeats steps 17 through 19 for each
additional configured tunnel you choose to create.
If you do not
want to create another IPv6-over-IPv6 configured tunnel, press Enter.
The procedure asks whether you want to configure manual IPv6 routes.
Configure manual IPv6 routes? [NO]:
|
If you want to configure a manual IPv6 route to an adjacent router
or remote IPv6 network, enter YES; subsequent prompts ask you for
information about the route. Otherwise, press Enter; the configuration
procedure continues at step 26.
Indicate the address prefix of a destination IPv6 network:
Enter the destination network address prefix:
|
Enter the IPv6 address prefix of the destination IPv6 network, or
enter DEFAULT for the default route.
Enter the name of the interface through which you will send traffic
to the remote IPv6 network:
Enter interface to use when forwarding messages:
|
Enter the link-local IPv6 address of the first router in the path
to the destination network. This address along with the IPv6 address
prefix constitute the static routing table entry.
Enter the next node's IPv6 address:
|
If the next node is on the same link as this node or is reachable
through a configured tunnel, enter the link-local address. If the next
node is reachable through an automatic tunnel, enter the
IPv4-compatible IPv6 address. For all other connections, enter the IPv6
address.
Indicate whether you want to define another manual route to an
adjacent router or remote IPv6 network:
Configure another manual IPv6 route? [NO]:
|
If you want to define another manual route, enter YES. The
configuration procedure repeats steps 22 through 24 for each additional
manual IPv6 route you choose to define. If you do not want to define
another manual route, press Enter.
At this point, the configuration procedure displays a summary of
your new IPv6 host configuration, as shown in the following example:
You configured this node as an IPv6 host with the
following:
Daemons:
ND6HOST Dynamic Updates Disabled
Interfaces:
WE0 Dynamic Address Configuration Enabled
TN1 6to4 Tunneling Enabled using 5.6.7.8
Prefix 2002:506:708::/64
Relay Router 2002:90A:B0C:1::1
Manual Routes:
2002::/16 TN1 FE80::5.6.7.8
DEFAULT TN1 2002:90A:B0C:1::1
|
The configuration procedure asks whether you want to create a new
host configuration file based on the choices you have made:
Create new IPv6 network configuration files? [YES]:
|
If you are not satisfied with the configuration, enter NO; the
configuration procedure ends immediately without changing the current
IPv6 network configuration.
If you are satisfied with the
configuration, press Enter. The configuration procedure creates a new
host configuration file and displays the following information:
A new IPv6 configuration file, SYS$SYSTEM:TCPIP$INET6_CONFIG.DAT,
has been created. The previous configuration file (if any) has been
renamed to SYS$SYSTEM:TCPIP$INET6_CONFIG.DAT_OLD.
This new IPv6 network configuration will become active the next time
TCP/IP Services for OpenVMS is started.
|
|
