/ACCESSED=n
Specifies, for ODS-1 disk volumes, the approximate number of
directories that will be in use concurrently on the volume. (The
/ACCESSED qualifier is meaningless for ODS-2 volumes.)
Specify a value from 0 to 255 to override the default that was
specified when the volume was initialized.
You need the user privilege OPER to use /ACCESSED.
Example
The following command requests the volume labeled WORK to be mounted on
DKA1, specifying 150 as the number of active directories on the volume:
$ MOUNT/ACCESSED=150 DKA1 WORK
|
/ASSIST (default)
/NOASSIST
Directs the mount operation to allow operator or user intervention if
the mount request fails.
When you specify the /ASSIST qualifier, MOUNT notifies the user and
certain classes of operator if a failure occurs during the mount
operation. If a failure occurs, the operator or user can either abort
the operation or correct the error condition to allow the operation to
continue.
The operator-assist messages are sent to all operator terminals that
are enabled to receive messages; magnetic tape mount requests go to
TAPE and DEVICE operators, and disk mount requests go to DISK and
DEVICE operators. Thus, if you need operator assistance while mounting
a disk device, a message is sent to DISK operators. See the description
of the REPLY command for more information about enabling and disabling
operator terminals.
Any operator reply to a mount request is written to SYS$OUTPUT to be
displayed on the user's terminal or written in a batch job log.
If no operator terminal is enabled to receive and respond to a mount
assist request, a message is displayed informing the user of the
situation. If a volume is placed in the requested drive, no additional
operator response is necessary. If the mount request originates from a
batch job and no operator terminal is enabled to receive messages, the
mount is aborted. See the OpenVMS System Messages: Companion Guide for Help Message Users for a description of the error
messages and their suggested user actions.
The default is /ASSIST and can be overridden by /NOASSIST.
Example
The following command mounts an HSG80 Fibre Channel disk volume labeled
DOC and assigns the logical name WORK. The /NOASSIST qualifier signals
MOUNT that no operator intervention is necessary.
$ MOUNT/NOASSIST $1$DGA0: DOC WORK
%MOUNT-I-MOUNTED, DOC mounted on _$1$DGA0: (NODE)
|
/AUTOMATIC (default)
/NOAUTOMATIC
Determines whether MOUNT enables or disables automatic volume switching
and labeling for magnetic tape or ISO 9660 CD-ROM.
Magnetic Tape
If you have multiple magnetic tape drives allocated to a volume set,
the magnetic tape ancillary control process (MTACP) performs the volume
switch by sequentially selecting the next available drive allocated to
the volume set. The MTACP expects the next reel of the volume set to be
loaded on that drive.
If the MTACP is writing to the volume set, it creates a label and
initializes the magnetic tape with that label and the protections
established for the first magnetic tape of the volume set. If it is
reading from the volume set, the MTACP generates the label and attempts
to mount the next magnetic tape with that label. If the drive has the
wrong magnetic tape (or no magnetic tape) loaded, the MTACP sends a
message to the operator's console to prompt for the correct magnetic
tape.
The label generated by the MTACP fills the 6-character volume
identifier field. The first four characters of the field contain the
first four characters of the label specified in the MOUNT command,
padded with underscores when the label is not at least four characters.
The fifth and sixth characters contain the relative volume number for
this reel in the volume set.
If you specify /NOAUTOMATIC, the MTACP requires operator intervention
to switch to the next drive during end-of-tape processing, and requires
that the operator specify a label for each new reel added to a volume
set.
ISO 9660 CD-ROM
Under ISO 9660, not all volume-set members must be mounted to perform
I/O operations against that volume set. By default, if I/O operations
attempt to access an unmounted volume-set member, an operator message
is sent to all DISK CLASS operators for system-mounted volume sets, or
the owning process for privately mounted volume sets. The message
specifies the volume-set member to mount to complete the I/O operation
requested. If /NOAUTOMATIC is specified, then an I/O operation to a
nonmounted volume set member completes with an error message
SS$_DEVNOTMOUNT.
Example
The following command instructs MOUNT not to generate its own label for
the second volume, but to use the ones supplied with the MOUNT command
instead. If the second volume is not already labeled, then the operator
must use REPLY/INIT and supply the second label.
$ MOUNT/NOAUTOMATIC MTA0: ABCD,EFGH
|
/BIND=volume-set-name
Creates a volume set of one or more disk volumes or adds one or more
volumes to an existing volume set.
The parameter, volume-set-name, specifies a 1- to
12-alphanumeric-character name identifying the volume set.
An ISO 9660 volume-set name can be from 1 to 128 characters in length.
OpenVMS requires volume-set names to be unique in the first 12
characters. In addition, if the first 12 characters of volume-set name
are the same as the first 12 characters of any volume label, a lock
manager deadlock will occur. To avoid this problem, you must override
either the volume label (by using the /OVERRIDE qualifier) or the
volume-set name (by using the /BIND qualifier).
You must specify the /BIND qualifier when you first create the volume
set or each time you add a volume to the set. To dismount an individual
volume of the volume set, you must use the DISMOUNT qualifier /UNIT;
otherwise, dismounting an individual volume dismounts the entire volume
set.
When you create a volume set, the volumes specified in the volume-label
list are assigned relative volume numbers based on their positions in
the label list. The first volume specified becomes the root volume of
the set.
When you add a volume or volumes to a volume set, the first volume
label specified must be that of the root volume, or the root volume
must already be on line.
Note that if you attempt to create a volume set from two or more
volumes that already contain files and data, the file system does not
issue an error message when you issue the MOUNT/BIND command. However,
the volumes are unusable as a volume set because the directory
structures are not properly bound.
If you mount an ISO 9660 volume using the /SYSTEM or /CLUSTER
qualifier, and the volume label is not unique within the first 12
characters, you must supply an alternate 12-character volume label
using the qualifier /BIND=volume-set-name. If you choose this option,
then Mount verification is disabled for the device.
Note
Once a volume is bound into a volume set, it cannot easily be unbound.
To unbind a bound volume set (BVS):
- Do an image backup of the BVS.
- Initialize all volumes of the BVS.
- Do an image restore to a single volume with the /NOINITIALIZE
qualifier, or do a nonimage restore to a single volume.
|
Examples
The following command creates a volume set named LIBRARY. This volume
set consists of the volumes labeled BOOK1, BOOK2, and BOOK3, which are
mounted physically on devices DMA0, DMA1, and DMA2, respectively.
$ MOUNT/BIND=LIBRARY DMA0:,DMA1:,DMA2: BOOK1,BOOK2,BOOK3
|
The following command creates a volume set with the logical name TEST3.
The volume set TEST3 is not shadowed, however each element of the
volume set (TEST3011 and TEST3012) is a shadow set, providing
redundancy for the volume set as a whole.
$ MOUNT/BIND=TEST3 DSA3011/SHADOW=($1$DUA402:,$1$DUA403:),
DSA3012/SHADOW=($1$DUA404:,$1$DUA405:) TEST3011,TEST3012 TEST3
|
/BLOCKSIZE=n
Specifies the default block size for magnetic tape volumes.
The parameter, n, specifies the default block size value for
magnetic tape volumes. Valid values are in the range 20 to 65,532 for
OpenVMS RMS operations, and 18 to 65,534 for non OpenVMS RMS
operations. By default, records are written to magnetic tape volumes in
2048-byte blocks. For foreign or unlabeled magnetic tapes, the default
is 512 bytes.
You must specify /BLOCKSIZE in two situations:
- When mounting magnetic tapes that do not have HDR2 labels. For
these magnetic tapes, you must specify the block size. For example, you
must specify /BLOCKSIZE=512 to mount an RT-11 magnetic tape.
- When mounting magnetic tapes that contain blocks whose sizes exceed
the default block size (2048 bytes). In this case, specify the size of
the largest block for the block size.
Example
In the following example, the /BLOCKSIZE qualifier specifies a block
size of 1000 bytes; the default for a magnetic tape mounted with the
/FOREIGN qualifier is 512.
$ MOUNT/FOREIGN/BLOCKSIZE=1000 MTA1:
|
/CACHE=(keyword[,...])
/NOCACHE
For disks, controls whether caching limits established at system
generation time are disabled or overridden. With the TAPE_DATA option,
enables write caching for the tape controller specified (if the tape
controller supports write caching).
The following table lists the keywords for this qualifier:
| Keyword |
Description |
|
DATA and NODATA
|
Enable or disable Extended File Caching (XFC). To enable XFC caching,
you must specify the DATA (this is the default value for /CACHE
qualifier). To disable XFC, specify NODATA. Note that /NOCACHE is
equivalent to /CACHE=NODATA.
|
|
EXTENT[=n] and NOEXTENT
|
Enable or disable extent caching. To enable extent caching, you must
have the operator user privilege (OPER) and you must specify
n, the number of entries in the extent cache. Note that
NOEXTENT is equivalent to EXTENT=0; both disable extent caching.
|
|
FILE_ID[=n] and NOFILE_ID
|
Enable or disable file identification caching. To enable file
identification caching, you must have the operator user privilege
(OPER) and you must specify
n, the number of entries, as a value greater than 1. Note that
NOFILE_ID is equivalent to FILE_ID=1; both disable file identification
caching.
|
|
LIMIT=n
|
Specifies the maximum amount of free space in the extent cache in
one-thousandths of the currently available free space on the disk.
|
|
QUOTA[=n] and NOQUOTA
|
Enable or disable quota caching. To enable quota caching, you must have
the operator user privilege (OPER) and you must specify
n, the number of entries in the quota cache. Normally
n is set to the maximum number of active users expected for a
disk with quotas enabled. Both NOQUOTA and QUOTA=0 disable quota file
caching.
|
|
TAPE_DATA
|
Enables write caching for a magnetic tape device if the tape controller
supports write caching. The /CACHE qualifier is the default for
mounting tape devices. You must specify TAPE_DATA to enable write
caching. If the tape controller does not support write caching, the
keyword is ignored.
The write buffer stays enabled even after you dismount the magnetic
tape. To disable the write buffer, mount a tape with the /NOCACHE
qualifier.
If a tape supports compaction, then the default is compaction, and
caching is enabled. For tape storage devices that support compaction,
the following command is valid:
$ MOUNT TAPE_DATA/FOREIGN/MEDIA=NOCOMPACTION/NOCACHE
|
|
WRITETHROUGH
|
Disables the deferred write feature for file headers. By default, this
feature is enabled, which improves the performance of applications,
such as PATHWORKS, that use it. The deferred write feature is not
available on Files-11 ODS-1 volumes.
|
Note
In a mixed-version OpenVMS cluster, an attempt to mount a volume with
/CLUSTER and /CACHE=[NO]DATA from a V8.4 system fails on the pre-V8.4
systems (%MOUNT-W-RMTMNTFAIL) with MOUNT-F-BADPARAM.
For more information on the restriction, see Enabling or Disabling
XFC While Mounting a Volume in the OpenVMS Version 8.4 New
Features and Documentation Overview manual.
|
Used with the disk options, the /CACHE qualifier overrides one or more
of the present disk caching limits established at system generation
time. Used with the TAPE_DATA option, the /CACHE qualifier enables
write caching for the tape controller specified.
If you do not specify the /CACHE qualifier and it is not implied by the
use of the qualifier /MEDIA_FORMAT=COMPACTION, caching is enabled by
default.
If you specify more than one option, separate them by commas and
enclose the list in parentheses. The options [NO]EXTENT, [NO]FILE_ID,
LIMIT, and [NO]QUOTA apply only to a disk device. The option TAPE_DATA
applies only to a tape device.
The /NOCACHE qualifier is effective only if compaction is not enabled.
If compaction is enabled (with the /MEDIA_FORMAT=COMPACTION), caching
is enabled by default.
If you specify /NOCACHE for a disk device, all caching is disabled for
this volume. Note that the /NOCACHE qualifier is equivalent to
/CACHE=(NOEXTENT, NOFILE_ID, NOQUOTA, WRITETHROUGH, NODATA).
In the following command, NODATA is taken as default when you supply
the following qualifiers NOEXTENT, NOFILE_ID, NOQUOTA, WRITETHROUGH
(that is, XFC is disabled):
$ MOUNT/CACHE=(NOEXTENT, NOFILE_ID, NOQUOTA, WRITETHROUGH)
_$ $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on $1$DGA0: (NODE)
|
In the following command, DATA is take as default (that is, XFC is
enabled):
$ MOUNT/CACHE=(FILE_ID=10)
_$ $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on $1$DGA0: (NODE)
|
If you specify /NOCACHE for a magnetic tape device, the tape
controller's write cache is disabled for this volume.
Examples
The following command mounts an HSG80 Fibre Channel disk device labeled
FILES and assigns the logical name WORK. The /CACHE qualifier enables
an extent cache of 60 entries, a file identification cache of 60
entries, and a quota cache of 20; it disables writeback caching of file
headers.
$ MOUNT/CACHE=(EXTENT=60,FILE_ID=60,QUOTA=20,WRITETHROUGH) -
_$ $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on _$1$DGA0: (NODE)
|
The following command mounts the volume TAPE on device MUA0 and
instructs MOUNT to enable the tape controller's write cache for MUA0:
$ MOUNT/CACHE=TAPE_DATA MUA0: TAPE
%MOUNT-I-MOUNTED, TAPE mounted on _NODE$MUA0:
|
The following command enables data cache (XFC) on a disk. The
/CACHE=DATA qualifier is the default value for a basic MOUNT command:
$ MOUNT/CACHE=(DATA)
_$ $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on $1$DGA0: (NODE)
|
The following command disables data cache (XFC) on a disk. /NOCACHE
qualifier is equivalent to /CACHE=(NODATA):
$ MOUNT/CACHE=(NODATA)
_$ $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on $1$DGA0: (NODE)
|
The following command disables data cache that is, XFC and metadata
cache that is, XQP. /NOCACHE qualifier is equivalent to /CACHE=(NODATA):
$ MOUNT/NOCACHE
_$ $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on $1$DGA0: (NODE)
|
/CLUSTER
Specifies that after the volume is successfully mounted on the local
node, or if it is already mounted /SYSTEM on the local node, it is to
be mounted on every other node in the existing OpenVMS Cluster (that
is, the volume is mounted clusterwide).
Only system or group volumes can be mounted clusterwide. If you specify
the /CLUSTER qualifier with neither the /SYSTEM nor the /GROUP
qualifier, the default is /SYSTEM. Note that you must use a cluster
device-naming convention. Use either node$device-name or
allocation-class$device-name as required by your configuration.
You need the user privileges GRPNAM and SYSNAM, respectively, to mount
group and system volumes clusterwide.
If the system is not a member of an OpenVMS Cluster, the /CLUSTER
qualifier has no effect.
Example
The following MOUNT/CLUSTER command mounts the volume SNOWWHITE on
DOPEY$DMA1, then proceeds to mount the volume clusterwide. The SHOW
DEVICE/FULL command displays information about the volume, including
the other nodes on which it is mounted.
$ MOUNT/CLUSTER DOPEY$DMA1: SNOWWHITE DWARFDISK
%MOUNT-I-MOUNTED, SNOWWHITE mounted on _DOPEY$DMA1:
$ SHOW DEVICE/FULL DWARFDISK:
Disk $2$DMA1: (DOPEY), device type RK07, is online, mounted,
file-oriented device, shareable, served to cluster via MSCP
Server, error logging is enabled.
Error count 0 Operations completed 159
Owner process "" Owner UIC [928,49]
Owner process ID 00000000 Dev Prot S:RWED,O:RWED,G:RW,W:R
Reference count 1 Default buffer size 512
Total blocks 53790 Sectors per track 22
Total cylinders 815 Tracks per cylinder 3
Allocation class 2
Volume label "SNOWWHITE" Relative volume number 0
Cluster size 3 Transaction count 1
Free blocks 51720 Maximum files allowed 6723
Extend quantity 5 Mount count 7
Mount status System Cache name "_$255$DWARF1:XQPCACHE"
Extent cache size 64 Maximum blocks in extent cache 5172
File ID cache size 64 Blocks currently in extent cache 0
Quota cache size 25 Maximum buffers in FCP cache 349
Volume status: ODS-2, subject to mount verification,
file high-water marking, write-through XQP caching enabled,
write-through XFC caching enabled.
Volume is also mounted on DOC, HAPPY, GRUMPY, SLEEPY, SNEEZY, BASHFUL.
|
/COMMENT=string
Specifies additional information to be included with the operator
request when the mount operation requires operator assistance.
The parameter, string, specifies a text string that is output
to the operator log file and the current SYS$OUTPUT device. The string
must contain no more than 78 characters.
Examples
The following command requests the operator to mount the disk volume
TESTSYS on the device DYA1. Notice that the /COMMENT qualifier is used
to inform the operator of the location of the volume. After the
operator places the volume in DYA1, MOUNT retries the operation. After
the operation completes, the operator request is canceled.
$ MOUNT DYA1: TESTSYS/COMMENT="Volume in cabinet 6."
%MOUNT-I-OPRQST, Please mount volume TESTSYS in device _DYA1:
Volume in cabinet 6.
%MOUNT-I-MOUNTED TESTSYS mounted on _DYA1:
%MOUNT-I-OPRQSTDON, operator request canceled - mount
completed successfully
|
The following command is the same as in the previous example. However,
in this example, because the requested device is in use, the operator
aborts the mount.
$ MOUNT DYA1: TESTSYS/COMMENT="Volume in cabinet 6."
%MOUNT-I-OPRQST, Please mount volume TESTSYS in device _DYA1:
Volume in cabinet 6.
%MOUNT-I-OPREPLY, This is a '/pending' response from the operator.
31-DEC-1990 10:27:38.15, request 2 pending by operator TTB6
%MOUNT-I-OPREPLY, This is a '/abort' response from the operator.
31-DEC-1990 10:29:59.34, request 2 aborted by operator TTB6
%MOUNT-F-OPRABORT, mount aborted by operator
|
The following command requests the operator to mount the volume TESTSYS
on the device DYA0. In this example, the operator notices that the
requested device is in use and redirects the mount to device DYA1.
$ MOUNT DYA0: TESTSYS/COMMENT="Volume in cabinet 6,
once again with feeling."
%MOUNT-I-OPRQST, Please mount volume TESTSYS in device _DYA0:
Volume in cabinet 6, once again with feeling.
%MOUNT-I-OPREPLY, Substitute DYA1:
31-DEC-1990 10:43:42.30, request 3 completed by operator TTB6
%MOUNT-I-MOUNTED, TESTSYS mounted on _DYA1:
|
/CONFIRM virtual-unit-name[:] /SHADOW=(physical-dev-name[:][,...])
/NOCONFIRM virtual-unit-name[:]
/SHADOW=(physical-dev-name[:][,...])
Causes MOUNT to pause and request confirmation before performing a copy
operation on the specified disk device. This qualifier is applicable
only if you have the volume shadowing option. See the HP Volume Shadowing for OpenVMS for
additional information.
This qualifier controls whether MOUNT issues a request to confirm a
full copy operation when mounting a shadow set. The /SHADOW qualifier
must be used with the /CONFIRM qualifier. Use /CONFIRM to display the
volume label and volume owner for any specified physical device that is
a target for a copy operation. MOUNT stops before any copy operations
occur and issues the following prompt:
Allow FULL shadow copy on the above member(s)? [N]:
|
If you respond Y or YES, the mount operation continues automatically
with copy operations allowed. If you respond N, NO, <RETURN>, or
<Ctrl/Z>, the command quits without mounting any of the specified
volumes (including volumes that did not require copy operations). If
you type a response other than those listed above, MOUNT reissues the
prompt.
The /CONFIRM qualifier is similar to /NOCOPY. Use /CONFIRM to mount
shadow sets interactively; use /NOCOPY in the site-specific startup
command procedure SYS$MANAGER:SYSTARTUP_VMS.COM.
Example
The following example shows how to use the /CONFIRM qualifier to check
the status of potential shadow set members before any data is erased.
The command instructs MOUNT to build a shadow set with the specified
devices, and prompts for permission to perform a copy operation. The
response of YES instructs MOUNT to mount the shadow set.
$MOUNT/CONFIRM DSA0:/SHADOW=($200$DKA200:,$200$DKA300:,$200$DKA400:) X5OZCOPY
|
%MOUNT-F-SHDWCOPYREQ, shadow copy required
Virtual Unit - DSA0 Volume Label - X5OZCOPY
Member Volume Label Owner UIC
$200$DKA200: (VIPER1) X5OZCOPY [SYSTEM]
$200$DKA400: (VIPER1) X5OZCOPY [SYSTEM]
Allow FULL shadow copy on the above member(s)? [N]:)
Y
|
%MOUNT-I-MOUNTED, X5OZCOPY mounted on _DSA0:
%MOUNT-I-SHDWMEMSUCC, _$200$DKA300: (VIPER1) is now a valid member of
the shadow set
%MOUNT-I-SHDWMEMCOPY, _$200$DKA200: (VIPER1) added to the shadow set
with a copy operation
%MOUNT-I-SHDWMEMCOPY, _$200$DKA400: (VIPER1) added to the shadow set
with a copy operation
|
/COPY virtual-unit-name[:] /SHADOW=(physical-dev-name[:][,...])
(default)
/NOCOPY virtual-unit-name[:]
/SHADOW=(physical-dev-name[:][,...])
Enables or disables copy operations on physical devices specified when
you mount a shadow set. This qualifier is applicable only if you have
the volume shadowing option. See the HP Volume Shadowing for OpenVMS for additional
information.
The /COPY qualifier instructs MOUNT to perform copy operations on
shadow set members. You can mount shadow sets with /NOCOPY to test if
proposed shadow set members are targets of copy operations. If any of
the specified volumes is a target of a copy operation, the command
quits without mounting any of the specified volumes (including those
that did not require a copy operation).
The /NOCOPY qualifier is similar to /CONFIRM. Use /NOCOPY to mount
shadow sets in the site-specific startup command procedure
SYS$MANAGER:SYSTARTUP_VMS.COM; use /CONFIRM for interactive mounting.
Example
The following example shows how to use the /NOCOPY qualifier to check
the status of potential shadow set members before any data is erased.
The command instructs MOUNT to build a shadow set with the specified
devices only if a copy operation is not required. Because the device
DUA7 required a copy operation to become a member of the shadow set,
the mount failed. You could reissue the command specifying /COPY to
instruct MOUNT to build the shadow set providing the necessary copy
operation.
$ MOUNT/NOCOPY DSA2: /SHADOW=($1$DUA4:,$1$DUA6:,$1$DUA7:) -
_$ SHADOWVOL DISK$SHADOWVOL
%MOUNT-F-SHDWCOPYREQ, shadow copy required
%MOUNT-I-SHDWMEMFAIL, DUA7: failed as a member of the shadow set
%MOUNT-F-SHDWCOPYREQ, shadow copy required
|
/DATA_CHECK[=(keyword[,...])]
Overrides the read-check or write-check option (or both) specified for
a volume when it was initialized.
The keyword, READ, performs checks following all read operations, and
the keyword, WRITE, performs checks following all write operations.
You can specify either or both of the keywords. If you specify more
than one keyword, separate them by commas and enclose the list in
parentheses.
If you specify the /DATA_CHECK qualifier without specifying a keyword,
MOUNT defaults to /DATA_CHECK=WRITE.
Example
The following command mounts a volume labeled SAM on CLEMENS$DKA2 and
assigns the logical name BOOK. The /DATA_CHECK=READ qualifier overrides
a previous INITIALIZE/DATA_CHECK=WRITE specification, so that
subsequent read operations on BOOK are subject to data-checking
operations.
$ MOUNT/DATA_CHECK=READ CLEMENS$DKA2: SAM BOOK
|
/DENSITY=keyword
Specifies the density at which a magnetic tape is to be written. This
qualifier is valid only if you mount a tape specifying the /FOREIGN
qualifier. If you change the density on a tape, the first operation on
the tape must be a write operation.
The densities supported for tapes are shown in the following table:
Table DCLI-13 Keywords for Tapes
| Keyword |
Meaning |
|
DEFAULT
|
Default density
|
|
800
|
NRZI 800 bits per inch (BPI)
|
|
1600
|
PE 1600 BPI
|
|
6250
|
GRC 6250 BPI
|
|
3480
|
IBM 3480 HPC 39872 BPI
|
|
3490E
|
IBM 3480 compressed
|
|
833
|
DLT TK50: 833 BPI
|
|
TK50
|
DLT TK50: 833 BPI
|
|
TK70
|
DLT TK70: 1250 BPI
|
|
6250
|
RV80 6250 BPI EQUIVALENT
|
|
NOTE: Only the symbols listed above are understood by TMSCP/TUDRIVER
code prior to OpenVMS Version 7.2. The remaining symbols in this table
are supported only on OpenVMS Alpha and Integrity server systems.
|
|
|
|
|
TK85
|
DLT Tx85: 10625 BPI---Cmpt III - Alpha/Integrity servers only
|
|
TK86
|
DLT Tx86: 10626 BPI---Cmpt III - Alpha/Integrity servers only
|
|
TK87
|
DLT Tx87: 62500 BPI---Cmpt III - Alpha/Integrity servers only
|
|
TK88
|
DLT Tx88: (Quantum 4000)---Cmpt IV - Alpha/Integrity servers only
|
|
TK89
|
DLT Tx89: (Quantum 7000)---Cmpt IV - Alpha/Integrity servers only
|
|
QIC
|
All QIC drives are drive-settable only - Alpha/Integrity servers only
|
|
|
|
|
TK85
|
DLT Tx85: 10625 BPI---Cmpt III - Alpha/Integrity servers only
|
|
TK86
|
DLT Tx86: 10626 BPI---Cmpt III - Alpha/Integrity servers only
|
|
TK87
|
DLT Tx87: 62500 BPI---Cmpt III - Alpha/Integrity servers only
|
|
TK88
|
DLT Tx88: (Quantum 4000)---Cmpt IV - Alpha/Integrity servers only
|
|
TK89
|
DLT Tx89: (Quantum 7000)---Cmpt IV - Alpha/Integrity servers only
|
|
QIC
|
All QIC drives are drive-settable only - Alpha/Integrity servers only
|
|
8200
|
Exa-Byte 8200 - Alpha/Integrity servers only
|
|
8500
|
Exa-Byte 8500 - Alpha/Integrity servers only
|
|
DDS1
|
Digital Data Storage 1---2G - Alpha/Integrity servers only
|
|
DDS2
|
Digital Data Storage 2---4G - Alpha/Integrity servers only
|
|
DDS3
|
Digital Data Storage 3---8-10G - Alpha/Integrity servers only
|
|
DDS4
|
Digital Data Storage 4 - Alpha/Integrity servers only
|
|
AIT1
|
Sony Advanced Intelligent Tape 1 - Alpha/Integrity servers only
|
|
AIT2
|
Sony Advanced Intelligent Tape 2 - Alpha/Integrity servers only
|
|
AIT3
|
Sony Advanced Intelligent Tape 3 - Alpha/Integrity servers only
|
|
AIT4
|
Sony Advanced Intelligent Tape 4 - Alpha/Integrity servers only
|
|
DLT8000
|
DLT 8000 - Alpha/Integrity servers only
|
|
8900
|
Exabyte 8900 - Alpha/Integrity servers only
|
|
SDLT
|
SuperDLT1 - Alpha/Integrity servers only
|
|
SDLT320
|
SuperDLT320 - Alpha/Integrity servers only
|
Note that tape density keywords cannot be abbreviated.
When you initialize a tape with the INITIALIZE command and do not
specify a density, the tape is initialized at the default density for
the media and drive you are using (usually the highest density
available).
The density of a tape can only be changed if the tape is at
beginning-of-tape (BOT). To change the density of a tape that has
previously been recorded, the first operation must be a write
operation. If the first operation on the tape is a read operation, the
magnetic tape is set to the density at which the first record on the
tape was recorded, no matter what density is specified with the
/DENSITY qualifier.
Example
The following command mounts a tape on the MFA0: drive /FOREIGN and
assigns it the logical name TAPE. The /DENSITY qualifier specifies that
the tape is to be written at TK87.
$ MOUNT/FOREIGN/DENSITY=TK87 MFA0: TAPE
|
/EXTENSION=n
Specifies the number of blocks by which disk files are to be extended
on the volume unless otherwise specified by an individual command or
program request.
The parameter, n, specifies a value from 0 to 65,535 to
override the value specified when the volume was initialized.
Example
The following command mounts a volume labeled DOC on DKA0, assigns the
logical name WORK, and specifies a default block extent of 64 for the
files on WORK:
$ MOUNT/EXTENSION=64 DKA0: DOC WORK
|
/FOREIGN
Indicates that the volume is not in the standard format used by the
OpenVMS operating system.
Use the /FOREIGN qualifier when a magnetic tape volume is not in the
standard ANSI format, or when a disk volume is not in Files-11 format.
If you mount a volume with the /FOREIGN qualifier, the program you use
to read the volume must be able to process the labels on the volume, if
any. The OpenVMS operating system does not provide an ancillary control
process (ACP) to process the volume.
You must mount DOS-1 and RT-11 volumes with the /FOREIGN qualifier and
process them with the Exchange utility (EXCHANGE). See the
OpenVMS Exchange Utility Manual (available on the Documentation CD-ROM).
The default protection applied to foreign volumes is RWLP (Read, Write,
Logical I/O, Physical I/O) for the system and owner and no access for
the group and world. If you also specify /GROUP, group members are also
given RWLP access. If you specify /SYSTEM or /SHARE, the group and
world are both given RWLP access. Note that the /GROUP, /SYSTEM, and
/SHARE qualifiers do not alter the default protection.
If you mount a volume currently in Files-11 format with the /FOREIGN
qualifier, you must have the user privilege VOLPRO, or your UIC must
match the UIC on the volume.
The /FOREIGN qualifier is incompatible with the following qualifiers:
/ACCESSED, /AUTOMATIC, /BIND, /CACHE, /[NO]CONFIRM, [NO]COPY,
/EXTENSION, /HDR3, /INITIALIZE, /LABEL, /PROCESSOR, /QUOTA, /REBUILD,
/SHADOW, /OVERRIDE=EXPIRATION, and /WINDOWS.
Examples
The following command mounts a foreign magnetic tape on drive MTA1:
$ MOUNT/FOREIGN MTA1: ABCD TAPE
|
The following command mounts an RK07 device as a foreign volume on DMA2
and assigns the default logical name as DISK$SAVEDISK. As a volume that
is not file structured, SAVEDISK can be used for sequential-disk BACKUP
save operations.
$ MOUNT/FOREIGN DMA2: SAVEDISK
|
/GROUP
Makes the volume available to other users with the same group number in
their UICs as the user entering the MOUNT command.
The logical name for the volume is placed in the group logical name
table. You must have the user privilege GRPNAM to use the /GROUP
qualifier.
Note that if the volume is owned by a group other than yours, access
may be denied because of the volume protection.
The /GROUP qualifier is not valid for ISO 9660 volume sets.
The /GROUP qualifier is incompatible with the /OVERRIDE=IDENTIFICATION,
/SHARE, and /SYSTEM qualifiers.
Examples
The following command mounts and makes available on a group basis the
volume set consisting of volumes labeled PAYVOL1, PAYVOL2, and PAYVOL3.
The logical name PAY is assigned to the set; anyone wanting to access
files on these volumes can refer to the set as PAY.
$ MOUNT/GROUP DB1:, DB2:, DB3: PAYVOL1,PAYVOL2,PAYVOL3 PAY
|
The following command adds the volume labeled PAYVOL4 to the existing
volume set MASTER_PAY. The root volume for the volume set must be on
line when you enter this command.
$ MOUNT/GROUP/BIND=MASTER_PAY DB4: PAYVOL4
|
/HDR3 (default)
/NOHDR3
Controls whether ANSI standard header label 3 is written on a magnetic
tape volume.
By default, header label 3 is written. You can specify the /NOHDR3
qualifier to write magnetic tapes that are to be used on other systems
that do not process HDR3 labels correctly.
Example
In the following example, the INITIALIZE and MOUNT commands prepare an
ANSI-formatted magnetic tape for processing. The /NOHDR3 qualifier
specifies that no HDR3 labels are to be written, thus creating a
magnetic tape that can be transported to systems that do not process
implementation-dependent labels correctly.
$ INITIALIZE MTA0: ABCD
$ MOUNT/NOHDR3 MTA0: ABCD
|
/INCLUDE virtual-unit-name[:]
/SHADOW=(physical-device-name[:][,...])
/NOINCLUDE virtual-unit-name[:]
/SHADOW=(physical-device-name[:][,...]) (default)
Automatically reconstructs a former shadow set to the way it was before
the shadow set was dissolved. This qualifier is applicable only if you
have the volume shadowing option. See the HP Volume Shadowing for OpenVMS for additional
information.
The /INCLUDE qualifier automatically mounts and restores a shadow set
to the way it was before a system failure. Supply the exact
virtual-unit name that was used when the shadow set was originally
mounted. Use the virtual-unit naming format DSAnnnn:.
You must also include the /SHADOW qualifier and specify at least one of
the disk devices from the original shadow set. Use the standard
device-naming format $allocation-class$ddcu[:]. Omit the parentheses if
you name only one device.
The /INCLUDE qualifier is position independent; it can appear anywhere
on the command line.
The default qualifier is /NOINCLUDE.
Example
The following example shows how to create a shadow set wherein the
software determines automatically the shadow set members that should be
mounted. The /SHADOW qualifier ensures the correct copy operation for
the two shadow set members. In this case, $1$DUA10 is the more current
volume and becomes the source of the copy operation to $1$DUA11.
If the shadow set was properly dismounted and no write I/O requests
remain outstanding, the shadow set devices are consistent and are added
back without the need for a copy or merge operation. Otherwise, Volume
Shadowing for OpenVMS automatically performs a copy or merge operation.
$ MOUNT/INCLUDE DSA0: /SHADOW=$1$DUA10: SHADOWVOL
%MOUNT-I-MOUNTED, SHADOWVOL mounted on DSA0:
%MOUNT-I-SHDWMEMSUCC, _$1$DUA10: (MEMBER1) is now a valid member of
the shadow set
%MOUNT-I-SHDWMEMCOPY, _$1$DUA11: (MEMBER2) added to the shadow set
with a copy operation
|
/INITIALIZE=CONTINUATION
Specifies that any volume added to the magnetic tape volume set is
initialized before you can write to the volume.
Example
The /INITIALIZE=CONTINUATION qualifier instructs the MOUNT command to
assign its own continuation label. In this case, the operator can enter
the command REPLY/BLANK=n, and the system assigns a label derived from
the original. It uses the label specified in the MOUNT command and adds
the appropriate number (ABCD02, ABCD03, and so forth).
$ MOUNT/INITIALIZE=CONTINUATION MTA0: ABCD
|
/LABEL (default)
/NOLABEL
Indicates that the volume is in the standard format used by the OpenVMS
operating system; that is, a magnetic tape volume is in the standard
ANSI format, or a disk volume is in Files-11 format.
The default is /LABEL.
Note that /NOLABEL is equivalent to /FOREIGN; they both set the FOREIGN
flag.
Example
The following command mounts an ANSI-labeled magnetic tape on MFA1 and
assigns the default logical name as TAPE$TAPE.
/MEDIA_FORMAT=CDROM
Mounts a volume assuming the media to be ISO 9660 (or High Sierra)
formatted.
The /MEDIA_FORMAT=CDROM qualifier instructs the mount subsystem to
attempt to mount a volume assuming the media to be ISO 9660 (or High
Sierra) formatted.
Note
This qualifier specifies a CD-ROM mount (ISO 9660 or High Sierra).
Specify this qualifier when a volume is known to be in either ISO 9660
or High Sierra CD-ROM format.
The Mount command attempts to read a CD-ROM in Files-11 ODS-2 format by
default. This qualifier prevents the Mount command from attempting a
Files-11 ODS-2 mount sequence.
Because it is possible to record parts of a CD-ROM in Files-11 ODS-2
and other parts in ISO 9660 format, this qualifier can be used to
specify a CD-ROM mount (ISO 9660 or High Sierra).
|
/MEDIA_FORMAT=[NO]COMPACTION
Enables and controls data compaction and data record blocking on tape
drives that support data compaction.
The /MEDIA_FORMAT qualifier allows you to mount a tape and enable data
compaction and record blocking on a tape drive that supports data
compaction. Data compaction and record blocking increase the amount of
data that can be stored on a single tape.
Records can either be compacted and blocked, or they can be recorded in
the same way that they would be recorded on a noncompacting tape drive.
Note that for compacting tape drives, once data compaction or
noncompaction has been selected for a given tape, that status applies
to the entire tape.
The /MEDIA_FORMAT=[NO]COMPACTION qualifier is incompatible with the
/DENSITY qualifier.
For Files-11 tapes, when you enable data compaction, caching is
automatically enabled.
Note
The /MEDIA_FORMAT=[NO]COMPACTION qualifier is meaningful only for
foreign mounts.
The /MEDIA_FORMAT=[NO]COMPACTION qualifier has no effect on a Files-11
tape. The compaction state of a Files-11 tape is determined by the
state established when the tape is initialized.
|
Examples
The following command performs a foreign mount of a tape with data
compaction and record blocking enabled and assigns the logical name
BOOKS to the tape:
$ MOUNT/FOREIGN/MEDIA_FORMAT=COMPACTION MUA0: BOOKS
|
The following MOUNT command attempts a Files-11 mount of a tape labeled
BOOKS with data compaction and record blocking enabled. Because the
tape was initialized with compaction disabled, the MOUNT qualifier
/MEDIA_FORMAT=COMPACTION has no effect.
$ INIT/MEDIA_FORMAT=NOCOMPACTION MUA0: BOOKS
$ MOUNT/MEDIA_FORMAT=COMPACTION MUA0: BOOKS
|
/MESSAGE (default)
/NOMESSAGE
Causes mount request messages to be sent to your current SYS$OUTPUT
device.
If you specify /NOMESSAGE during an operator-assisted mount, messages
are not output to SYS$OUTPUT; the operator sees them, however, provided
an operator terminal is enabled.
Example
In this example, an RL02 device labeled SLIP is mounted on drive DLA0
and is assigned the logical name DISC. The /NOMESSAGE qualifier
disables the broadcast of mount request messages to the user terminal.
$ MOUNT/NOMESSAGE DLA0: SLIP DISC
|
/MOUNT_VERIFICATION (default)
/NOMOUNT_VERIFICATION
Specifies that the device is a candidate for mount verification.
The /MOUNT_VERIFICATION qualifier affects the following media:
- Files-11 Structure Level 2 or 5 disks (mount verification is not
supported for foreign-mounted disks)
- ISO 9660 and High Sierra CD-ROMs
- Foreign and ANSI-labeled magnetic tape volumes
Example
The following command mounts an HSG80 Fibre Channel disk device labeled
FILES and assigns the logical name WORK. The /CACHE qualifier disables
extent caching, file identification caching, quota caching, data
caching, and writeback caching; the /NOMOUNT_VERIFICATION qualifier
disables mount verification.
$ MOUNT/CACHE=(NOEXTENT,NOFILE_ID,NOQUOTA,WRITETHROUGH) -
_$ /NOMOUNT_VERIFICATION $1$DGA0: FILES WORK
%MOUNT-I-MOUNTED, FILES mounted on _$1$DGA0: (NODE)
|
/MULTI_VOLUME
/NOMULTI_VOLUME (default)
For foreign or unlabeled magnetic tape volumes, determines whether you
override MOUNT volume-access checks.
Use /MULTI_VOLUME to override access checks on volumes that do not
contain labels that MOUNT can interpret. If you have software produced
before OpenVMS Version 5.0 that processes multiple-volume,
foreign-mounted tape volumes without specifically mounting and
dismounting each reel, you may now need to mount the first volume with
the /MULTI_VOLUME qualifier.
Use this qualifier when a utility that supports multiple-volume,
foreign-mounted magnetic tape sets needs to process subsequent volumes,
and these volumes do not contain labels that the OpenVMS Mount command
can interpret.
By default, all tape volumes are subject to the complete access checks
of the OpenVMS Mount command (MOUNT). Some user-written and
vendor-supplied utilities used prior to OpenVMS Version 5.0 may mount
only the first tape in a foreign tape set. To make these utilities
compatible with more recent versions of OpenVMS, alter them to perform
explicit calls to the $MOUNT and $DISMOU system services for each reel
in the set. As an alternative, you can now mount the magnetic tape sets
to be used by these utilities with the /MULTI_VOLUME qualifier.
You must specify the /FOREIGN qualifier with the /MULTI_VOLUME
qualifier and you must have the user privilege VOLPRO. The default is
/NOMULTI_VOLUME.
Note
The OpenVMS Backup utility (BACKUP) explicitly calls the $MOUNT and
$DISMOU system services on each reel of a foreign-mounted magnetic tape
set. For additional information, see the section on multivolume save
sets and BACKUP in the HP OpenVMS System Management Utilities Reference Manual: A--L.
|
Example
The following command mounts a tape volume set. MOUNT performs an
access check on the first volume in the set and proceeds without checks
to subsequent reels as they are needed for processing.
$ MOUNT/FOREIGN/MULTI_VOLUME MUA0:
|
/OVERRIDE=(keyword[,...])
Inhibits one or more protection checks that the MOUNT command performs.
You need the user privileges OPER and VOLPRO to specify
/OVERRIDE=(ACCESSIBILITY, EXPIRATION) along with the /FOREIGN
qualifier; otherwise, the magnetic tape is not read.
If you specify more than one keyword, separate them with commas and
enclose the list in parentheses.
The following table lists the keywords for this qualifier:
| Keyword |
Description |
|
ACCESSIBILITY
|
For magnetic tapes only. If the installation allows, this keyword
overrides any character in the Accessibility Field of the volume. The
necessity of this keyword is defined by the installation. That is, each
installation has the option of specifying a routine that the magnetic
tape file system will use to process this field. By default, the
OpenVMS operating system provides a routine that checks this field in
the following manner:
- If the magnetic tape was created on a version of OpenVMS that
conforms to Version 3 of ANSI, then you must use this keyword to
override any character other than an ASCII space.
- If an OpenVMS protection is specified and the magnetic tape
conforms to an ANSI standard that is higher than Version 3, then you
must use this keyword to override any character other than an ASCII 1.
To use the ACCESSIBILITY keyword, you must have the user privilege
VOLPRO or own the volume.
|
|
EXPIRATION
|
For magnetic tapes only. Allows you to override the expiration dates of
a volume and its files. Use this keyword when the expiration date in
the first file header label of any file that you want to overwrite has
not been reached. You must have the user privilege VOLPRO or your UIC
must match the UIC written on the volume.
|
|
IDENTIFICATION
|
Overrides processing of the volume identifier in the volume label. Use
this keyword to mount a volume for which you do not know the label, or
for an ISO 9660 volume whose label is not unique in the first 12
characters. Only the volume identifier field is overridden. Volume
protection, if any, is preserved. The volume must be mounted /NOSHARE
(either explicitly or by default).
The /OVERRIDE=IDENTIFICATION qualifier is incompatible with the
/GROUP and /SYSTEM qualifiers.
|
|
LIMITED_SEARCH
|
Allows the Mount command to search an entire device for a home block,
if a home block is not found at the expected location. By default, the
search for a home block is limited to avoid excessive search times if
no valid home block is present.
|
|
LOCK
|
Directs MOUNT not to write-lock the volume as a consequence of certain
errors encountered while mounting it. Use this keyword when you are
mounting a damaged volume to be repaired using the
ANALYZE/DISK_STRUCTURE command. You must have VOLPRO privilege or own
the volume to use the LOCK keyword.
|
|
NO_FORCED_ERROR
|
Directs the Mount command to proceed with shadowing, even though the
device or controller does not support forced error handling. Using
unsupported SCSI disks can cause members to be removed from a shadow
set if certain error conditions arise that cannot be corrected, because
some SCSI disks do not implement READL and WRITEL commands that support
disk bad block repair.
|
|
OWNER_IDENTIFIER
|
For magnetic tapes only. Overrides the processing of the owner
identifier field. Use this keyword to interchange protected magnetic
tapes between OpenVMS and other HP operating systems.
|
|
SECURITY
|
Allows you to continue mounting a volume if an error is returned
because the volume has an invalid SECURITY.SYS file. You must have the
user privilege VOLPRO or own the volume to use this keyword.
|
|
SETID
|
For magnetic tapes only. Prevents MOUNT from checking the file-set
identifier in the first file header label of the first file on a
continuation volume. Use this keyword only for ANSI-labeled volumes on
which the file-set identifier of the first file on a continuation
volume differs from the file-set identifier of the first file of the
first volume that was mounted.
|
|
SHADOW_MEMBERSHIP
|
Allows you to override the write protection of former shadow set
members. Applicable only if you have the volume shadowing option. See
the HP Volume Shadowing for OpenVMS.
When you mount a volume with this qualifier, the volume shadowing
generation number is erased. If you attempt to remount the volume in a
shadow set, the volume is considered an unrelated volume and receives a
full copy operation from a current shadow set member.
|
The following command overrides the volume identification field, thus
mounting a magnetic tape on MFA0 without a label specification:
$ MOUNT/OVERRIDE=IDENTIFICATION MFA0:
|
/OWNER_UIC=uic
Requests that the specified UIC be assigned ownership of the volume
while it is mounted, overriding the ownership recorded on the volume.
If you are mounting a volume using the /FOREIGN qualifier, requests an
owner UIC other than your current UIC.
The parameter, uic, specifies the user identification code
(UIC) in the following format:
[group,member]
You must use brackets in the UIC specification. The group number is an
octal number in the range 0 to 37776; the member number is an octal
number in the range 0 to 177776.
To use the /OWNER_UIC qualifier for a Files-11 volume, you must have
the user privilege VOLPRO, or your UIC must match the UIC written on
the volume.
Example
The following command mounts a disk device labeled WORK on DRA3 and
assigns an owner UIC of [016,360]:
$ MOUNT/OWNER_UIC=[016,360] DRA3: WORK
|
/POLICY=[NO]MINICOPY[=(OPTIONAL)], REQUIRE_MEMBERS,
[NO]VERIFY_LABEL
Controls the setup and use of shadow sets. For more information about
volume shadowing, see the HP Volume Shadowing for OpenVMS.
The following table lists the keywords for this qualifier:
| Keyword |
Description |
|
[NO]MINICOPY [=OPTIONAL] (Alpha/Integrity servers only)
|
Controls the setup and use of the shadowing minicopy function.
Requires LOG_IO (logical I/O) privilege to create
bitmaps.
The meaning of the keyword [NO]MINICOPY[=OPTIONAL] for the
MOUNT/POLICY qualifier depends on the status of the shadow set, as
follows:
- If the shadow set is not mounted, either on a standalone system or
on any cluster member, and MINICOPY=OPTIONAL is specified, the shadow
set is mounted and a write bitmap is created. The write bitmap enables
a shadowing minicopy operation. You must specify
/MOUNT/POLICY=MINICOPY[=OPTIONAL] on the initial mount of a shadow set,
either on a standalone system or in a cluster, to enable the shadowing
minicopy operation.
The OPTIONAL keyword allows the mount to continue, even if the
system was unable to start the write bitmap. Likely reasons for the
bitmap to fail to start properly include an improperly dismounted
shadow set, a shadow set that requires a merge operation, and various
resource problems. If the OPTIONAL keyword is omitted and the system is
unable to start the write bitmap, the shadow set will not be mounted.
If you specify the /POLICY=MINICOPY=OPTIONAL qualifier and the
shadow set was already mounted on another node in the cluster without
the /POLICY=MINICOPY[=OPTIONAL], the MOUNT command succeeds but a write
bitmap is not created.
If NOMINICOPY is specified, the shadow set is mounted but a write
bitmap is not created.
- If a former member of the shadow set is returned to the shadow set,
which has minicopy enabled, then a minicopy is started instead of a
full copy. This is the default behavior and will occur even if you omit
/POLICY=MINICOPY[=OPTIONAL]. If a minicopy is successfully started and
then fails for some reasons, a full copy is performed.
If a minicopy cannot be started and the keyword OPTIONAL was
omitted, the mount will fail.
If NOMINICOPY is specified, then no minicopy is performed, even if
one is possible.
|
|
REQUIRE_MEMBERS
|
Controls whether every physical device specified with the /SHADOW
qualifier must be accessible when the MOUNT command is issued in order
for the MOUNT command to take effect. The proposed members are either
specified in the command line or found on the disk by means of the
/INCLUDE qualifier.
The behavior, without this qualifier, is that if one or more
members is not accessible for any reason (such as a connectivity
failure), then the virtual unit will be created with the members that
are accessible.
This option is especially useful in the recovery of
disaster-tolerant clusters because it ensures that the correct
membership is selected after an event.
|
|
[NO]VERIFY_LABEL
|
Require that any member that is going to be added to the shadow set
must have a volume label of 'SCRATCH_DISK'.
This will help insure that the wrong disk is not added to a shadow
set by mistake. If VERIFY_LABEL is going to be used, then the disk that
is going to be added to the set must be either initialized with the
label 'SCRATCH_DISK' or a SET VOLUME/LABEL must be performed.
The default behavior is NOVERIFY_LABEL, which indicates that the
volume label of the copy targets will not be checked.
|
/PROCESSOR=keyword
For magnetic tapes and Files-11 Structure Level 1 disks, requests that
the MOUNT command associate an ancillary control process (ACP) to
process the volume. The /PROCESSOR qualifier causes MOUNT to override
the default manner in which ACPs are associated with devices.
For Files-11 Structure Levels 2 and 5 disks, controls block cache
allocation.
The following table lists the keywords for this qualifier:
| Keyword |
Description |
|
UNIQUE
|
Creates a new process to execute the default ancillary control process
(ACP) image supporting the magnetic tape, Files-11 ODS-1, ISO 9660, or
High Sierra formatted media being mounted.
For Files-11 Structure Levels 2 and 5 disks, allocates a separate
block cache.
|
|
SAME:device
|
Uses an existing process that is executing the same ACP image
supporting the magnetic tape, Files-11 ODS-1, ISO 9660, or High Sierra
formatted media being mounted.
For Files-11 Structure Levels 2 and 5 disks, takes the block cache
allocation from the specified device.
|
|
file-spec
|
Creates a new process to execute the ACP image specified by the file
specification (for example, a modified or a user-written ACP). You
cannot use wildcard characters, or node and directory names in the file
specification.
To use this keyword, you need CMKRNL and OPER privileges.
You must have the operator user privilege OPER to use the
/PROCESSOR qualifier.
|
Example
The following command directs MOUNT to mount a magnetic tape on MFA0
using the same ACP process currently associated with MTA1:
$ MOUNT/PROCESSOR=SAME:MTA1: MFA0:
|
/PROTECTION=keyword
Specifies the protection code to be assigned to the volume.
The following table describes the keywords for this qualifier:
| Keyword |
Description |
|
protection code
|
Specifies the protection code according to the standard syntax rules
for specifying user protection (that is, system/owner/group/world). If
you omit a protection category, that category of user is denied all
access.
If you do not specify a protection code, the default is the
protection that was assigned to the volume when it was initialized.
|
|
XAR
|
Enables enforcement of the extended record attribute (XAR) access
controls. For more information about XAR, see the OpenVMS Record Management Services Reference Manual.
|
|
DSI
|
Enables XAR permissions Owner and Group for XARs containing Digital
System Identifiers (DSI). For more information, see the OpenVMS Record Management Services Reference Manual.
|
If you specify the /PROTECTION qualifier when you mount a volume with
the /SYSTEM or /GROUP qualifier, the specified protection code
overrides any access rights implied by the other qualifiers.
If you specify the /FOREIGN qualifier, the execute (E) or create (C)
and delete (D) access codes are synonyms for logical I/O (L) and
physical I/O (P). You can, however, specify the access codes physical
I/O (P) or logical I/O (L), or both, to restrict the nature of
input/output operations that different user categories can perform.
To use the /PROTECTION qualifier on a Files-11 volume, you must have
the user privilege VOLPRO or your UIC must match the UIC written on the
volume.
Example
The following command mounts a device labeled WORKDISK on DKA1 and
assigns a protection code. Access to the volume will be read, write,
and create for system users; read, write, create, and delete for owner;
read and create for group users; and read-only for users in the world
category.
$ MOUNT/PROTECTION=(SYSTEM:RWE,O:RWED,G:RE,W:R) DKA1: WORKDISK
|
/QUOTA (default)
/NOQUOTA
Controls whether quotas are to be enforced on the specified disk volume.
The default is /QUOTA, which enforces the quotas for each user. The
/NOQUOTA qualifier inhibits this checking. To specify the /QUOTA
qualifier, you must have the user privilege VOLPRO or your UIC must
match the UIC written on the volume.
Example
The following command specifies that the disk volume labeled WORK on
DRA3 has an owner UIC of [016,360] and no quotas enforced:
$ MOUNT/OWNER_UIC=[016,360]/NOQUOTA DRA3: WORK
|
/REBUILD (default)
/NOREBUILD
Controls whether or not MOUNT performs a rebuild operation on a disk
volume.
If a disk volume is improperly dismounted (such as during a system
failure), you must rebuild it to recover any caching limits that were
enabled on the volume at the time of the dismount. By default, MOUNT
attempts the rebuild. For a successful rebuild operation that includes
reclaiming all of the available free space, you must mount all
of the volume set members.
The rebuild may consume a considerable amount of time, depending on the
number of files on the volume and, if quotas are in use, on the number
of different file owners.
The following caches may have been in effect on the volume before it
was dismounted:
- Preallocated free space (EXTENT cache)
- Preallocated file numbers (FILE_ID cache)
- Disk quota usage caching (QUOTA cache)
If caching was in effect for preallocated free space or file numbers,
the rebuild time is directly proportional to the greatest number of
files that ever existed on the volume at one time. If disk quota
caching was in effect, you can expect additional time that is
proportional to the square of the number of entries in the disk quota
file.
If none of these items were in effect, the rebuild is not necessary and
does not occur.
If you use the /NOREBUILD qualifier, devices can be returned to active
use immediately. You can then perform the rebuild later with the DCL
command SET VOLUME/REBUILD.
For information about how to rebuild the system disk, see the
HP OpenVMS System Manager's Manual.
Examples
In this example, the volume WORKDISK is mounted on NODE$DKA2. Because
the volume is found to have been improperly dismounted and the /REBUILD
qualifier is in effect, MOUNT displays a message and proceeds to
rebuild the volume.
$ MOUNT/REBUILD NODE$DKA2: WORKDISK
%MOUNT-I-MOUNTED, WORKDISK mounted on _NODE$DKA2:
%MOUNT-I-REBUILD, volume was improperly dismounted; rebuild in
progress
|
In this example, the volume WORKDISK is found to have been improperly
dismounted, but because the /NOREBUILD qualifier is specified, a
rebuild is not performed. Instead, MOUNT displays a message to inform
you that the rebuild is needed, and proceeds to make WORKDISK available
for use as is. You can rebuild the volume later with the DCL command
SET VOLUME/REBUILD.
$ MOUNT/NOREBUILD NODE$DKA2: WORKDISK
%MOUNT-I-MOUNTED, WORKDISK mounted on _NODE$DKA2:
%MOUNT-I-REBLDREQD, rebuild not performed; some free space
unavailable; diskquota usage stale
|
/RECORDSIZE=n
Specifies the number of characters in each record of a magnetic tape
volume.
The parameter, n, specifies the block size in the range 20 to
65,532 bytes if you are using OpenVMS RMS, or 18 to 65,534 bytes if you
are not using OpenVMS RMS.
You typically use this qualifier with the /FOREIGN and /BLOCKSIZE
qualifiers to read or write fixed-length records on a block-structured
device. In this case, the record size must be less than or equal to the
block size specified or used by default.
Use the /RECORDSIZE qualifier when mounting magnetic tapes without HDR2
labels (such as RT-11 magnetic tapes) to provide OpenVMS RMS with
default values for the maximum record size.
Example
In the following example, the magnetic tape is mounted on MTA0 with a
default block size and record size of 512 characters:
$ MOUNT/FOREIGN/BLOCKSIZE=512/RECORDSIZE=512 MTA0:
|
/SHADOW
Binds up to three physical devices into a shadow set represented by the
virtual unit named in the command. This qualifier is applicable only if
you have the volume shadowing option. See the HP Volume Shadowing for OpenVMS for
additional information.
The format of this qualifier is:
(virtual-unit-name[:] /SHADOW=(physical-device-name[:][,...]))
|
This qualifier indicates that you are mounting a shadow set including
the physical devices and the virtual unit that represents them to the
system. This qualifier instructs MOUNT to expect a virtual unit name as
the device-name parameter. Place the /SHADOW qualifier after
the virtual-unit-name parameter.
Use the virtual unit naming format DSAn, where n is a
unique number from 0 to 9999. For the physical-device-name,
use the standard device-naming format $allocation-class$ddcu[:].
Examples
The following example shows how to create a shadow set wherein the
software determines automatically the correct copy operation for the
two shadow set members. In this case, $1$DUA10 is the more current
volume and becomes the source of the copy operation to $1$DUA11.
$ MOUNT DSA0: /SHADOW=($1$DUA10:,$1$DUA11:) SHADOWVOL
%MOUNT-I-MOUNTED, SHADOWVOL mounted on DSA0:
%MOUNT-I-SHDWMEMSUCC, _$1$DUA10: (MEMBER1) is now a valid member of
the shadow set
%MOUNT-I-SHDWMEMCOPY, _$1$DUA11: (MEMBER2) added to the shadow set
with a copy operation
|
The following command creates a volume set with the logical name
TEST3013. The volume set TEST3013 is not shadowed. However, each
element of the volume set (TEST3011 and TEST3012) is a shadow set,
providing redundancy for the volume set as a whole.
$ MOUNT/BIND=TEST3013 DSA3011/SHADOW=($1$DUA402:,$1$DUA403:),
DSA3012/SHADOW=($1$DUA404:,$1$DUA405:) TEST3011,TEST3012 TEST3013
|
/SHARE
/NOSHARE
Specifies, for a disk volume, that the volume is shareable.
If another user has already mounted the volume shareable, and you
request it to be mounted with the /SHARE qualifier, any other
qualifiers you enter are ignored.
By default, a volume is not shareable, and the MOUNT command allocates
the device on which it is mounted.
If you previously allocated the device and specify the /SHARE
qualifier, the MOUNT command deallocates the device so that other users
can access it.
The /SHARE qualifier is incompatible with the /GROUP and /SYSTEM
qualifiers.
Example
The following command mounts the device labeled SLIP on DLA0, disables
broadcasting of MOUNT messages, specifies that the volume is shareable,
and assigns the logical name DISC:
$ MOUNT/NOMESSAGE/SHARE DLA0: SLIP DISC
|
/SUBSYSTEM
/NOSUBSYSTEM
Enables protected subsystems and the processing of subsystem ACEs.
Requires the SECURITY privilege.
By default, the disk from which you boot has /SUBSYSTEM enabled but
other disks do not. For further details on subsystems, see the
HP OpenVMS Guide to System Security.
Example
The following command mounts the volume labeled SLIP on DUA1 with mount
messages disabled. Subsystems on the volume are accessible. MOUNT also
assigns the logical name SACH.
$ MOUNT/NOMESSAGE/SUBSYSTEM DUA1: SLIP SACH
|
/SYSTEM
Makes the volume public; that is, available to all users of the system,
as long as the UIC-based volume protection allows them access.
The logical name for the device is placed in the system logical name
table. You must have the user privilege SYSNAM to use the /SYSTEM
qualifier.
When you mount a volume with the /SYSTEM qualifier in a VMScluster
system, you must use a volume label that is unique clusterwide, even if
the specified volume is not mounted clusterwide.
The /SYSTEM qualifier is incompatible with the /GROUP,
/OVERRIDE=IDENTIFICATION, and /SHARE qualifiers.
Examples
The following command mounts the volume labeled SLIP on DUA1 with mount
messages disabled. The volume is made available systemwide. MOUNT also
assigns the logical name SACH.
$ MOUNT/NOMESSAGE/SYSTEM DUA1: SLIP SACH
|
The following command creates the volume set named MASTER_PAY
consisting of the initialized volumes labeled PAYVOL1, PAYVOL2, and
PAYVOL3. These volumes are mounted physically on the devices named DB1,
DB2, and DB3, respectively. The volume PAYVOL1 is the root volume of
the set.
The volumes are mounted as system volumes to make them available to all
users.
$ MOUNT/SYSTEM/BIND=MASTER_PAY -
_$ DB1:,DB2:,DB3: PAYVOL1,PAYVOL2,PAYVOL3
|
/UCS_SEQUENCE=escape_sequence
Supplies the escape sequence to select the coded graphic character set,
a requirement when mounting an ISO 9660 volume for one of the
Supplementary Volume Descriptors (SVDs).
The parameter, escape_sequence, is a character sequence
defined by the vendor who mastered the CD-ROM and is unique to the
vendor's character set conversion tables.
Use the /UCS_SEQUENCE qualifier when mounting an ISO 9660 CD-ROM that
contains non-ASCII character sets on OpenVMS.
An ISO 9660 volume may contain an SVD that specifies a graphic
character set. This graphic character, when selected at mount time, is
used as default character set when displaying a volume's directories
and file names.
The /UCS_SEQUENCE qualifier defines the escape sequence to select the
coded graphic character set.
All ISO 9660 volumes contain a Primary Volume Descriptor (PVD) that
uses ASCII (ISO 646-IRV) as the character set. Both ISO 9660 and
OpenVMS file naming conventions use the same subset of ASCII characters
when displaying a volume's directories and file names.
/UNDEFINED_FAT=record-format:[record-attributes:][record-size]
Establishes default file attributes to be used for records on ISO 9660
media for which no record format has been specified.
The following table describes the parameters:
| Parameter |
Description |
|
record-format
|
Specifies the format for all records in a file: FIXED, VARIABLE,
STREAM, STREAM_LF, STREAM_CR, LSB_VARIABLE, or MSB_VARIABLE. For a
description of these record formats, see the discussion of the RMS
field FAB$B_RFM in the OpenVMS Record Management Services Reference Manual.
|
|
record-attributes
|
Specifies the attributes for all records in a file: NONE, CR, FTN, PRN,
NOBKS. Applies only to non-STREAM record formats. For a description of
these record attributes, see the discussion of the RMS field FAB$B_RAT
in the OpenVMS Record Management Services Reference Manual.
|
|
record-size
|
Specifies the maximum record size for all records in a file: 0 to
32767. Applies only to FIXED or STREAM record formats. For a
description of possible RMS record sizes, see the discussion of the RMS
field FAB$W_MRS in the OpenVMS Record Management Services Reference Manual.
|
ISO 9660 media can be mastered from platforms that do not support
semantics of files containing predefined record formats. The
/UNDEFINED_FAT qualifier establishes default file attributes to be used
for records on ISO 9660 media for which no record format has been
specified.
The /UNDEFINED_FAT qualifier is valid only in conjunction with the
/MEDIA_FORMAT=CDROM qualifier.
This qualifier temporarily overrides all undefined file types,
replacing them with selectable record formats having selectable record
attributes and selectable record sizes as shown in the following
illustration:
In the following example, the volume labeled OFFENS is mounted on DKA1
and all files on the volume are defined to be fixed length, carriage
return, and 80 bytes in length. MOUNT also assigns the logical name
STRAT.
In the following example, the volume labeled OFFENS is mounted on DKA1
with the /NOUNLOAD qualifier so that it can be dismounted without being
physically unloaded. MOUNT also assigns the logical name STRAT.
When a file is opened, the file system uses the mapping pointers to
access data in the file. Use MOUNT/WINDOWS to override the default
value specified when the volume was initialized. If no value was
specified at volume initialization, the default number of mapping
pointers is 7.
You must have the operator user privilege (OPER) to use the /WINDOWS
qualifier.
By default, a volume is considered read/write when it is mounted. You
can specify /NOWRITE to provide read-only access to protect files. This
is equivalent to write-locking the device.
For host-based volume shadowing devices, there are other
considerations. See the HP Volume Shadowing for OpenVMS manual for more information.
The following command mounts a volume labeled BOOKS on NODE$DKA1 and
then proceeds to mount it on each node in the existing OpenVMS Cluster.
The /NOWRITE qualifier makes the volume available for read-only access.
