/CR
/NOCR (default)
Controls whether the printer driver outputs a carriage return
character. Use this qualifier for printers on which line feeds do not
imply carriage returns.
Specify the /NOCR qualifier for printers where the line feed, form
feed, vertical feed, and carriage return characters empty the printer
buffer. The /NOCR qualifier causes carriage return characters to be
held back and output only if the next character is not a form feed or
vertical tab. Carriage return characters are always output on devices
that have the carriage return function characteristic set.
/FALLBACK
/NOFALLBACK (default)
Determines whether the printer attempts to translate characters
belonging to the DEC Multinational character set into 7-bit equivalent
representations. If a character cannot be translated, an underscore (_)
character is substituted.
If the /PASSALL qualifier is in effect, it has precedence over the
/FALLBACK qualifier.
/FF (default)
/NOFF
Indicates whether the printer performs a mechanical form feed. Use the
/NOFF qualifier when the printer does not automatically perform
mechanical form feeds. This qualifier allows the driver to convert form
feeds into multiple line feeds and to output them.
/LA11
Specifies the printer as an LA11. This qualifier provides information
for the SHOW PRINTER command, which, in turn, provides the user with
information about specific printers. If no printer type is specified,
LP11 is assumed.
/LA180
Specifies the printer as an LA180. This qualifier provides information
for the SHOW PRINTER command, which, in turn, provides the user with
information about specific printers. If no printer type is specified,
LP11 is assumed.
/LOG
/NOLOG (default)
Determines whether information confirming the printer setting is
displayed at the terminal from which the SET PRINTER command was
entered.
/LOWERCASE
/NOLOWERCASE
Indicates whether the printer prints both uppercase and lowercase
letters or only uppercase. When the operator specifies the /NOLOWERCASE
qualifier, all letters are translated to uppercase.
The /[NO]LOWERCASE and /[NO]UPPERCASE qualifiers are complementary;
that is, the /LOWERCASE qualifier is equivalent to the /NOUPPERCASE
qualifier, and the /NOLOWERCASE qualifier is equivalent to the
/UPPERCASE qualifier.
/LP11 (default)
Specifies the printer as an LP11. This qualifier provides information
for the SHOW PRINTER command, which, in turn, provides the user with
information about specific printers. LP11 is the default printer type.
/PAGE=lines-per-page
Establishes the number of lines per page on the currently installed
form; the number of lines can range from 1 to 255 and defaults to 64.
The printer driver uses this value to determine the number of line
feeds that must be entered to simulate a form feed.
/PASSALL
/NOPASSALL (default)
Controls whether the system interprets special characters or passes
them as 8-bit binary data.
If you specify the /PASSALL qualifier, the printer driver does not
expand tab characters to spaces, fill carriage return or line feed
characters, or recognize control characters.
/POLLED
/NOPOLLED (default)
Instructs the LRDRIVER to run in polled mode instead of interrupt mode.
In polled mode, the printer is checked on a regular basis to determine
if it is ready to receive additional data. The polling timer runs only
while there is more data to be sent to the printer.
/PRINTALL
/NOPRINTALL (default)
Controls whether the line printer driver outputs printable 8-bit
multinational characters.
/RESET
Resets the USB pipe associated with the USB printer, thereby canceling
all print jobs.
/TAB
/NOTAB (default)
Controls how the printer handles TAB characters. The /NOTAB qualifier
expands all tab characters to spaces and assumes tab stops at
8-character intervals.
Use the /TAB qualifier when you do not want the system to convert tabs
to spaces, but want the printer to process the tab characters. The
OpenVMS system requires that printers expand tabs at 8-character
intervals.
/TRUNCATE (default)
/NOTRUNCATE
Controls whether the printer truncates data exceeding the value
specified by the /WIDTH qualifier. Note that the /TRUNCATE and /WRAP
qualifiers are incompatible.
/UNKNOWN
Specifies the printer as nonstandard. This qualifier provides
information for the SHOW PRINTER command, which, in turn, provides the
user with information about specific printers. If no printer type
qualifier is specified, LP11 is assumed.
/UPPERCASE
/NOUPPERCASE
Indicates whether the printer prints both uppercase and lowercase
letters or only uppercase ones. When you specify the /UPPERCASE
qualifier, all letters are translated to uppercase.
The /[NO]UPPERCASE and /[NO]LOWERCASE qualifiers are complementary;
that is, the /UPPERCASE qualifier is equivalent to the /NOLOWERCASE
qualifier, and the /NOUPPERCASE qualifier is equivalent to the
/LOWERCASE qualifier.
/WIDTH=n
Establishes the number of characters per output line on currently
installed forms. The width, n, can range from 0 to 65535 for
LP11 controllers, and from 0 to 255 for DMF32 controllers. The default
value is 132 characters per line.
/WRAP
/NOWRAP (default)
Controls whether the printer generates a carriage return and a line
feed when it reaches the end of a line.
If the /NOWRAP qualifier is specified, the printer writes characters
out in the last position on the line.
If the /WRAP qualifier is specified, the terminal generates a carriage
return and a line feed whenever the end of a line is reached.
Note that the /TRUNCATE and /WRAP qualifiers are incompatible.
