![]() |
Software > OpenVMS Systems > Ask the Wizard ![]() HP OpenVMS Systemsask the wizard |
![]() |
The Question is: I have a ALPHA DEC3000/M300 machine. It runs at this moment V 7.2-1. I can do everything with the cd-rom station without any problems. But I want to now install V 7.2-2. Then I get problem to find the cd-rom. Start up the system. (V 7.2-1) en inloggen as system. $show device d Device Name Status MAXLU$DKB100: Online wrtlck MAXLU$DKB300: Online MAXLU$DKB400: Online MAXLU$DKB500: Online MAXLU$DKB600: Online MAXLU$DKC0: Mounted MAXLU$DKC200: Online **** You can see at the cd-rom MAXLU$DKB100 $shutdown >>> show device BOOTDEV ADDR DEVTYPE NUMBYTES ------- ---- ------- -------- ESA0 08-00-2B-BE-56-7A , TENBT DKA0 A/0/0 DISK 1.05GB DKA200 A/2/0 DISK 1.05GB ..HostID.. A/7 INITR >>> ***** Now I can't see the cd-rom station >>> t tc0 cnfg DEC PMAZB-AA V1.7 (Dual SCSI [53C96]) BOOTDEV ADDR DEVTYPE NUMBYTES ------- ---- ------- -------- ..HostID.. A/7 INITR DKB100 B/1/0 RODISK ...... (rz100B) DKB300 B/3/0 DISK 4GB (rz300B) DKB400 B/4/0 DISK 4GB (rz400B) DKB500 B/5/0 DISK 2GB (rz500B) DKB600 B/6/0 DISK 2GB (rz600B) ..HostID.. B/7 INITR >>> ***** Now I can see the DKB100 >>> Boot DKB100 (where is the V 7.2-2 software) INIT-S-CPU... INIT-S-ASIC... INIT-S-MEM... INIT-S-NVR... INIT-S-CXT... INIT-S-SCC... INIT-S-NI... INIT-S-SCSI... INIT-S-ISDN... INIT-S-TC0... AUDIT_BOOT_STARTS ... 84 FAIL >>> boot tc0/dkb100 INIT-S-CPU... INIT-S-ASIC... INIT-S-MEM... INIT-S-NVR... INIT-S-CXT... INIT-S-SCC... INIT-S-NI... INIT-S-SCSI... INIT-S-ISDN... INIT-S-TC0... AUDIT_BOOT_STARTS ... 84 FAIL What I have to do? Help me please. The Answer is : Please review The OpenVMS Alpha Upgrade and Installation Manual. In particular, the appendix on Halt, Boot, and Shutdown Procedures describes booting OpenVMS on DEC 3000 systems via Turbochannel options. In your case, the correct command to boot the device with SCSI ID 1 on the "B" channel of the PMAZB adapter in Turbochannel slot 0 is: >>> BOOT "0/DKB100" This syntax, including the quotation marks, is required. In addition, some CD-ROM devices do not respond correctly for a short time after a SCSI bus reset. You may need to increase the value of the SCSI_RESET console environment variable. The recommended value for CD-ROMs is 6, but lower values may work depending on the drive and the SCSI bus configuration. For example: >>> SET SCSI_RESET 6 Finally, the latest firmware for the PMAZB-AA adapter is V2.0. Please obtain and install current firmware from the AlphaServer firmware web pages.
|