HP OpenVMS Systems Documentation

OpenVMS Cluster Systems

The transport (TR) header is used to pass SCS datagrams and sequenced messages between cluster nodes. The important fields for network troubleshooting are the TR datagram flags, message acknowledgment, and sequence numbers. Note that because the CC and TR headers occupy the same space, a TR/CC flag identifies the type of message being transmitted over the channel.

Figure F-10 shows the portions of the TR header that are needed for network troubleshooting, and Table F-11 describes these fields.

Figure F-10 TR Header

Note: The TR header shown in Figure F-10 is used when both nodes are running Version 1.4 or later of the NISCA protocol. If one or both nodes are running Version 1.3 or an earlier version of the protocol, then both nodes will use the message acknowledgment and sequence number fields in place of the extended message acknowledgment and extended sequence number fields, respectively.

Some failures, such as packet loss resulting from congestion, intermittent network interruptions of less than 20 seconds, problems with backup bridges, and intermittent performance problems, can be difficult to diagnose. Intermittent failures may require the use of a LAN analysis tool to isolate and troubleshoot the NISCA protocol levels described in Section F.1.

As you evaluate the various network analysis tools currently available, you should look for certain capabilities when comparing LAN analyzers. The following sections describe the required capabilities.

F.8.1 Single or Multiple LAN Segments

Whether you need to troubleshoot problems on a single LAN segment or on multiple LAN segments, a LAN analyzer should help you isolate specific patterns of data. Choose a LAN analyzer that can isolate data matching unique patterns that you define. You should be able to define data patterns located in the data regions following the LAN header (described in Section F.7.2). In order to troubleshoot the NISCA protocol properly, a LAN analyzer should be able to match multiple data patterns simultaneously.

To troubleshoot single or multiple LAN segments, you must minimally define and isolate transmitted and retransmitted data in the TR header (see Section F.7.7). Additionally, for effective network troubleshooting across multiple LAN segments, a LAN analysis tool should include the following functions:

• A distributed enable function that allows you to synchronize multiple LAN analyzers that are set up at different locations so that they can capture information about the same event as it travels through the LAN configuration
• A distributed combination trigger function that automatically triggers multiple LAN analyzers at different locations so that they can capture information about the same event

The purpose of distributed enable and distributed combination trigger functions is to capture packets as they travel across multiple LAN segments. The implementation of these functions discussed in the following sections use multicast messages to reach all LAN segments of the extended LAN in the system configuration. By providing the ability to synchronize several LAN analyzers at different locations across multiple LAN segments, the distributed enable and combination trigger functions allow you to troubleshoot LAN configurations that span multiple sites over several miles.

F.8.2 Multiple LAN Segments

To troubleshoot multiple LAN segments, LAN analyzers must be able to capture the multicast packets and dynamically enable the trigger function of the LAN analyzer, as follows:

The HP 4972A LAN Protocol Analyzer, available from the Hewlett-Packard Company, is one example of a network failure analysis tool that provides the required functions described in this section.

Reference: Section F.10 provides examples that use the HP 4972A LAN Protocol Analyzer.

F.9 Data Isolation Techniques

The following sections describe the types of data you should isolate when you use a LAN analysis tool to capture OpenVMS Cluster data between nodes and LAN adapters.

F.9.1 All OpenVMS Cluster Traffic

To isolate all OpenVMS Cluster traffic on a specific LAN segment, capture all the packets whose LAN header contains the protocol type 60--07.

Reference: See also Section F.7.2 for a description of the LAN headers.

F.9.2 Specific OpenVMS Cluster Traffic

To isolate OpenVMS Cluster traffic for a specific cluster on a specific LAN segment, capture packets in which:

• The LAN header contains the the protocol type 60--07.
• The DX header contains the cluster group number specific to that OpenVMS Cluster.

Reference: See Sections F.7.2 and F.7.5 for descriptions of the LAN and DX headers.

F.9.3 Virtual Circuit (Node-to-Node) Traffic

To isolate virtual circuit traffic between a specific pair of nodes, capture packets in which the LAN header contains:

• The protocol type 60--07
• The destination SCS address
• The source SCS address

You can further isolate virtual circuit traffic between a specific pair of nodes to a specific LAN segment by capturing the following additional information from the DX header:

• The cluster group code specific to that OpenVMS Cluster
• The destination SCS transport address
• The source SCS transport address

Reference: See Sections F.7.2 and F.7.5 for LAN and DX header information.

F.9.4 Channel (LAN Adapter--to--LAN Adapter) Traffic

To isolate channel information, capture all packet information on every channel between LAN adapters. The DX header contains information useful for diagnosing heavy communication traffic between a pair of LAN adapters. Capture packets in which the LAN header contains:

• The destination LAN adapter address
• The source LAN adapter address

Because nodes can use multiple LAN adapters, specifying the source and destination LAN addresses may not capture all of the traffic for the node. Therefore, you must specify a channel as the source LAN address and the destination LAN address in order to isolate traffic on a specific channel.

Reference: See Section F.7.2 for information about the LAN header.

F.9.5 Channel Control Traffic

To isolate channel control traffic, capture packets in which:

• The LAN header contains the the protocol type 60--07.
• The CC header datagram flags byte (the TR/CC flag, bit <7>) is set to 1.

Reference: See Sections F.7.2 and F.7.6 for a description of the LAN and CC headers.

F.9.6 Transport Data

To isolate transport data, capture packets in which:

• The LAN header contains the the protocol type 60--07.
• The TR header datagram flags byte (the TR/CC flag, bit <7>) is set to 0.

Reference: See Sections F.7.2 and F.7.7 for a description of the LAN and TR headers.

F.10 Setting Up an HP 4972A LAN Protocol Analyzer

The HP 4972A LAN Protocol Analyzer, available from the Hewlett-Packard Company, is highlighted here because it meets all of the requirements listed in Section F.8. However, the HP 4972A LAN Protocol Analyzer is merely representative of the type of product useful for LAN network troubleshooting.

Note: Use of this particular product as an example here should not be construed as a specific purchase requirement or endorsement.

This section provides some examples of how to set up the HP 4972A LAN Protocol Analyzer to troubleshoot the local area OpenVMS Cluster system protocol for channel formation and retransmission problems.

F.10.1 Analyzing Channel Formation Problems

If you have a LAN protocol analyzer, you can set up filters to capture data related to the channel control header (described in Section F.7.6).

You can trigger the LAN analyzer by using the following datagram fields:

• Protocol type set to 60--07 hexadecimal
• Correct cluster group number
• TR/CC flag set to 1

Then look for the HELLO, CCSTART, VERF, and VACK datagrams in the captured data. The CCSTART, VERF, VACK, and SOLICIT_SRV datagrams should have the AUTHORIZE bit (bit <4>) set in the CC flags byte. Additionally, these messages should contain the scrambled cluster password (nonzero authorization field). You can find the scrambled cluster password and the cluster group number in the first four longwords of SYS$SYSTEM:CLUSTER_AUTHORIZE.DAT file.

Reference: See Sections F.9.3 through F.9.5 for additional data isolation techniques.

F.10.2 Analyzing Retransmission Problems

Using a LAN analyzer, you can trace datagrams as they travel across an OpenVMS Cluster system, as described in Table F-12.

Reference: See Appendix G for more information about congestion control and PEDRIVER message retransmission.

F.11 Filters

This section describes:

• How to use the HP 4972A LAN Protocol Analyzer filters to isolate packets that have been retransmitted or that are specific to a particular OpenVMS Cluster.
• How to enable the distributed enable and trigger functions.

Use the values shown in Table F-13 to set up a filter, named LAVc_TR_ReXMT, for all of the LAN retransmissions for a specific cluster. Fill in the value for the local area OpenVMS Cluster group code (nn--nn) to isolate a specific OpenVMS Cluster on the LAN.

Use the values shown in Table F-14 to filter all of the LAN packets for a specific cluster. Fill in the value for OpenVMS Cluster group code (nn--nn) to isolate a specific OpenVMS Cluster on the LAN. The filter is named LAVc_all.