Although older versions of CDSA are pre-installed on OpenVMS
Version 7.3-2 and Version 8.2, you can install and run CDSA Version
2.2.
CDSA Version
2.2 Setup and Initialization |
 |
If you want to run CDSA Version 2.2 on OpenVMS Version
8.2 or 7.3-2, you must manually install the CDSA Version 2.2
kit, which is included on the OpenVMS Version 8.3 media. Use
the following command to install CDSA Version 2.2 on an OpenVMS
Version 8.2 or 7.3-2 system:
$ PRODUCT INSTALL CDSA /SOURCE=disk:[directory] |
The following product has been selected:
CPQ AXPVMS CDSA V2.2 Layered Product
Do you want to continue? [YES]
Configuration phase starting ...
You will be asked to choose options, if any, for each selected product and for
any products that may be installed to satisfy software dependency requirements.
CPQ AXPVMS CDSA V2.2
Do you want the defaults for all options? [YES]
Do you want to review the options? [NO]
Execution phase starting ...
The following product will be installed to destination:
CPQ AXPVMS CDSA V2.2 DISK$SYSTEM:[VMS$COMMON.]
Portion done:
0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100%
The following product has been installed:
CPQ AXPVMS CDSA V2.2 Layered Product
CPQ AXPVMS CDSA V2.2
$ |
Before you can use CDSA Version 2.2. you must perform the
following manual procedure, for which you must have SYSPRV privileges.
Execute the following command to initialize CDSA Version 2.0:
$ @SYS$STARTUP:CDSA$UPGRADE |
This procedure automatically runs CDSA$INITIALIZE. It is not
necessary to rerun any initialization procedure when the system
is rebooted; therefore, you do not need to add the initialization
to the OpenVMS startup procedures.
The CDSA$UPGRADE procedure can take a few minutes, depending
on your processor and disk speeds. When the procedure is run interactively,
you will see system messages similar to the following:
CDSA-I-Init, CDSA has previously been initialized on this system.
CDSA-I-Init, Re-initializing CDSA.
CDSA-I-Init, Initializing CDSA
MDS installed successfully.
Module uninstalled successfully.
Module uninstalled successfully.
Module uninstalled successfully.
Module uninstalled successfully.
Module uninstalled successfully.
Module uninstalled successfully.
Module uninstalled successfully.
Module uninstalled successfully.
CDSA-I-Init, CDSA Initialization complete
CDSA-I-Init, Initializing Secure Delivery
Install completed successfully.
Install completed successfully.
Module installed successfully.
Module installed successfully.
CDSA-I-Init, Secure Delivery Initialization complete
$ |
Warning
Against Uninstalling CDSA from OpenVMS Alpha Version 7.3-1 or Higher |
|
The POLYCENTER Software Installation utility command PRODUCT
REMOVE is not supported for CDSA on OpenVMS Alpha Version 7.3-1
or higher, even though there is an apparent option to remove CDSA.
(This option is due to the use of the POLYCENTER Software Installation
utility in the installation.) CDSA is installed together with the
operating system and is tightly bound with it. An attempt to remove
it from Version 7.3-1 or higher would not work cleanly and could
create other undesirable side effects. An attempt to remove CDSA
results in the following message:
%PCSI-E-HRDREF, product CPQ AXPVMS CDSA Vx.x is
referenced by DEC AXPVMS OPENVMS V7.3-2
-PCSI-E-HRDRF1, the two products are tightly bound
by this software dependency |
